100483

Original build: June 1941

Serial No.: 100483     D.W.W.          J.A.N.
Model No.: 10L
Catalogue No.: 987 R
Swing: 10L
Length of bed: 4 ½ ft.
Spindle OD thread: 2 Ό "-8 tpi
Spindle through hole: 1 3/8” (1.426”)
Spindle length: 13 11/16”
Original Motor: HP: 3/4, PH: 1, CYCLE: 60, VOLTS: 115 AC, SPEED: 1725 (RPM), MAKE: GE, TYPE: KC, MODEL: 5KC73AB 254, SERIAL NO.: ?, FRAME:  ?, TEMP. RATING; 50 °, (2-STEP PULLEYS), Switch: 790

Replacement Motor: HP: 3/4, PH: 1, CYCLE: 60, VOLTS: 115/230 AC, AMP: 9.5/4.75, RPM: 1725, MAKE: GE, TYPE: KC, MODEL: 5KC65AB586X, SERIAL NO.: ?, FRAME: 65A    ZD   \T, TEMP. RISE: 40 °C, TIME RATING: CONT., (2-STEP PULLEY)

Tooling & Accessories

Chuck: 3 jaw, 6 3/8”, Cushman, Registration No. 3560B SN: 91 101 06 200B.  (Back stamp; 10L 13)
Collet set, 5C, (15 collets; 1/16” through 1”) w/ drawbar and 3C nose cone adapter.
Face plates: 5 ½” & 8 3/8”
Face plate drive dogs: Ύ” (Vulcan No. 3) 1 3/8”, 1 ½” (Armstrong? No. 601)
Follow rest
Tool post: Standard lantern type (1 3/8” base slot width)
Tool holders:  7/16” wide. x 7/8” high x ~ 4” long for Ό” square tools
·	Straight, (No name)
·	Straight, (Armstrong No. S-0)
·	Right hand (Armstrong No. R-0)
·	Left hand (Armstrong No. L-0)
·	Knurling, diamond (Armstrong No. 83-673)
·	Cutoff (Armstrong No. S-20)
·	Boring bar, 9/16” bar with 3/16” square tool (Armstrong No. 8)
Tail stock MT#2
Dead center MT#2
Live center, 9/16” cone, MT#2
Live center, 7/8” cone, MT#2
Drill chuck, 3/8”, MT#2
Drill chuck, ½”, MT#2
MT#1 to MT#2 adapter
MT#3 to MT#2 adapter
MT#2 to MT#3 adapter

Literature

Parts, & operating manual SBCE3458
Lubrication chart
“How to Run a Lathe”, 42nd Edition, 1941
“Keep Your Lathe in Trim”

History:

Original build: June 1941

Shipped to: Hazelton service Corp., Little Neck, New York, July 9, 1941.

Thomas Jividen acquired from Gerald Tidwell of Union Town, Pennsylvania.

Ashley Edmunds purchased from Thomas Jividen (friend at work @Toyota in Buffalo, WV) for $350 in late summer 2005

Joe Bragg purchased from Ashley Edmunds for $350 on 03-29-2008

Owner identification marks found on the lathe:
·	H. Leach Machinery Co., Machine Tools & Equipment, 45-75 Corliss Street, Providence, RI 02904 (pinned metal tag)
·	Asset tag # 02206, “Property of William Bloom & Sons, Inc.”
·	# “L8473” embossed on pinned metal tag
·	# “155” stenciled in yellow paint on leg